Linux Kernel up to 6.18.5/6.19-rc4 idpf_detach_and_close null pointer dereference

Summaryinfo

A vulnerability marked as critical has been reported in Linux Kernel up to 6.18.5/6.19-rc4. The impacted element is the function idpf_detach_and_close. Performing a manipulation results in null pointer dereference. This vulnerability is identified as CVE-2026-22981. There is not any exploit available. It is suggested to upgrade the affected component.

Detailsinfo

A vulnerability was found in Linux Kernel up to 6.18.5/6.19-rc4. It has been classified as critical. This affects the function idpf_detach_and_close. The manipulation with an unknown input leads to a null pointer dereference vulnerability. CWE is classifying the issue as CWE-476. A NULL pointer dereference occurs when the application dereferences a pointer that it expects to be valid, but is NULL, typically causing a crash or exit. This is going to have an impact on availability. The summary by CVE is:

In the Linux kernel, the following vulnerability has been resolved: idpf: detach and close netdevs while handling a reset Protect the reset path from callbacks by setting the netdevs to detached state and close any netdevs in UP state until the reset handling has completed. During a reset, the driver will de-allocate resources for the vport, and there is no guarantee that those will recover, which is why the existing vport_ctrl_lock does not provide sufficient protection. idpf_detach_and_close() is called right before reset handling. If the reset handling succeeds, the netdevs state is recovered via call to idpf_attach_and_open(). If the reset handling fails the netdevs remain down. The detach/down calls are protected with RTNL lock to avoid racing with callbacks. On the recovery side the attach can be done without holding the RTNL lock as there are no callbacks expected at that point, due to detach/close always being done first in that flow. The previous logic restoring the netdevs state based on the IDPF_VPORT_UP_REQUESTED flag in the init task is not needed anymore, hence the removal of idpf_set_vport_state(). The IDPF_VPORT_UP_REQUESTED is still being used to restore the state of the netdevs following the reset, but has no use outside of the reset handling flow. idpf_init_hard_reset() is converted to void, since it was used as such and there is no error handling being done based on its return value. Before this change, invoking hard and soft resets simultaneously will cause the driver to lose the vport state: ip -br a <inf> UP echo 1 > /sys/class/net/ens801f0/device/reset& \ ethtool -L ens801f0 combined 8 ip -br a <inf> DOWN ip link set <inf> up ip -br a <inf> DOWN Also in case of a failure in the reset path, the netdev is left exposed to external callbacks, while vport resources are not initialized, leading to a crash on subsequent ifup/down: [408471.398966] idpf 0000:83:00.0: HW reset detected [408471.411744] idpf 0000:83:00.0: Device HW Reset initiated [408472.277901] idpf 0000:83:00.0: The driver was unable to contact the device's firmware. Check that the FW is running. Driver state= 0x2 [408508.125551] BUG: kernel NULL pointer dereference, address: 0000000000000078 [408508.126112] #PF: supervisor read access in kernel mode [408508.126687] #PF: error_code(0x0000) - not-present page [408508.127256] PGD 2aae2f067 P4D 0 [408508.127824] Oops: Oops: 0000 [#1] SMP NOPTI ... [408508.130871] RIP: 0010:idpf_stop+0x39/0x70 [idpf] ... [408508.139193] Call Trace: [408508.139637] <TASK> [408508.140077] __dev_close_many+0xbb/0x260 [408508.140533] __dev_change_flags+0x1cf/0x280 [408508.140987] netif_change_flags+0x26/0x70 [408508.141434] dev_change_flags+0x3d/0xb0 [408508.141878] devinet_ioctl+0x460/0x890 [408508.142321] inet_ioctl+0x18e/0x1d0 [408508.142762] ? _copy_to_user+0x22/0x70 [408508.143207] sock_do_ioctl+0x3d/0xe0 [408508.143652] sock_ioctl+0x10e/0x330 [408508.144091] ? find_held_lock+0x2b/0x80 [408508.144537] __x64_sys_ioctl+0x96/0xe0 [408508.144979] do_syscall_64+0x79/0x3d0 [408508.145415] entry_SYSCALL_64_after_hwframe+0x76/0x7e [408508.145860] RIP: 0033:0x7f3e0bb4caff

It is possible to read the advisory at git.kernel.org. This vulnerability is uniquely identified as CVE-2026-22981 since 01/13/2026. The exploitability is told to be difficult. Technical details of the vulnerability are known, but there is no available exploit.

The vulnerability scanner Nessus provides a plugin with the ID 296409 (Linux Distros Unpatched Vulnerability : CVE-2026-22981), which helps to determine the existence of the flaw in a target environment.

Upgrading to version 6.18.6 or 6.19-rc5 eliminates this vulnerability. Applying the patch ac122f5fb050903b3d262001562c452be95eaf70/2e281e1155fc476c571c0bd2ffbfe28ab829a5c3 is able to eliminate this problem. The bugfix is ready for download at git.kernel.org. The best possible mitigation is suggested to be upgrading to the latest version.

The vulnerability is also documented in the databases at Tenable (296409) and CERT Bund (WID-SEC-2026-0215). Be aware that VulDB is the high quality source for vulnerability data.

Affected

• Debian Linux
• Amazon Linux 2
• Red Hat Enterprise Linux
• Ubuntu Linux
• SUSE Linux
• Oracle Linux
• IBM QRadar SIEM
• SUSE openSUSE
• RESF Rocky Linux
• NetApp ActiveIQ Unified Manager
• Open Source Linux Kernel

Productinfo

Type

• Operating System

Vendor

• Linux

Name

• Kernel

Version

• 6.18.0
• 6.18.1
• 6.18.2
• 6.18.3
• 6.18.4
• 6.18.5
• 6.19-rc1
• 6.19-rc2
• 6.19-rc3
• 6.19-rc4

License

• open-source

Website

• Vendor: https://www.kernel.org/

CPE 2.3info

• 🔒
• 🔒
• 🔒

CPE 2.2info

• 🔒
• 🔒
• 🔒

CVSSv4info

CVSSv3info

CVSSv2info

Exploitinginfo

Threat Intelligenceinfo

Countermeasuresinfo

Timelineinfo

Sourcesinfo

Entryinfo

Be aware that VulDB is the high quality source for vulnerability data.

Discussion