Linux Kernel up to 7.1.4 LWT Tunnel include/linux/skbuff.h skb_data_move input validation

Summaryinfo

A vulnerability marked as very critical has been reported in Linux Kernel up to 7.1.4. Affected by this vulnerability is the function skb_data_move of the file include/linux/skbuff.h of the component LWT Tunnel. Performing a manipulation results in input validation. This vulnerability is identified as CVE-2026-80612. The attack can be initiated remotely. There is not any exploit available.

Detailsinfo

A vulnerability, which was classified as very critical, was found in Linux Kernel up to 7.1.4. This affects the function skb_data_move of the file include/linux/skbuff.h of the component LWT Tunnel. The manipulation with an unknown input leads to a input validation vulnerability. CWE is classifying the issue as CWE-20. The product receives input or data, but it does not validate or incorrectly validates that the input has the properties that are required to process the data safely and correctly. This is going to have an impact on confidentiality, integrity, and availability. The summary by CVE is:

In the Linux kernel, the following vulnerability has been resolved: net: lwtunnel: Drop skb metadata before LWT encapsulation skb metadata is meant for passing information between XDP and TC. It lives in the skb headroom, immediately before skb->data. LWT programs cannot access the __sk_buff->data_meta pseudo-pointer to metadata. However, LWT encapsulation prepends outer headers, moving skb->data back over the headroom where the metadata sits. On an RX-originated (forwarded) packet that still carries XDP metadata this goes wrong in two different ways, depending on the encap type: 1. Non-BPF LWT encaps (mpls, seg6, ioam6 ...) call skb_push()/skb_pull() and silently overwrite the metadata that sits in the headroom. 2) BPF LWT xmit calls bpf_skb_change_head(), which uses skb_data_move(). That helper expects metadata immediately before skb->data. But since the IP output path runs LWT xmit before neighbour output has built the outgoing L2 header, for forwarded packets skb->data points at the L3 header while skb_mac_header() still points at the old L2 header. skb_data_move() sees metadata ending at skb_mac_header(), not before skb->data, warns and clears metadata: WARNING: CPU: 21 PID: 454557 at include/linux/skbuff.h:4609 skb_data_move+0x47/0x90 CPU: 21 UID: 0 PID: 454557 Comm: napi/iconduit-g Tainted: G O 6.18.21 #1 RIP: 0010:skb_data_move+0x47/0x90 Call Trace: <IRQ> bpf_skb_change_head+0xe6/0x1a0 bpf_prog_...+0x213/0x2e3 run_lwt_bpf.isra.0+0x1d3/0x360 bpf_xmit+0x46/0xe0 lwtunnel_xmit+0xa1/0xf0 ip_finish_output2+0x1e7/0x5e0 ip_output+0x63/0x100 __netif_receive_skb_one_core+0x85/0xa0 process_backlog+0x9c/0x150 __napi_poll+0x2b/0x190 net_rx_action+0x40b/0x7f0 handle_softirqs+0xd2/0x270 do_softirq+0x3f/0x60 </IRQ> That is what happens, as for how to fix it - a received packet that carries metadata can reach an encap through any of the three LWT redirect modes: LWTUNNEL_STATE_INPUT_REDIRECT ip6_rcv_finish dst_input lwtunnel_input LWTUNNEL_STATE_OUTPUT_REDIRECT ip6_rcv_finish dst_input ip6_forward ip6_forward_finish dst_output lwtunnel_output LWTUNNEL_STATE_XMIT_REDIRECT ip6_rcv_finish dst_input ip6_forward ip6_forward_finish dst_output ip6_output ip6_finish_output ip6_finish_output2 lwtunnel_xmit Every encap funnels through the three LWT dispatch helpers, so drop the metadata there, right before handing the skb to the encap op. This single chokepoint covers all encap types and all three redirect modes: - lwtunnel_input(): seg6, rpl, ila, seg6_local - lwtunnel_output(): ioam6 - lwtunnel_xmit(): mpls, LWT BPF xmit Alternatively, we could clear the metadata right after TC ingress hook. That would require a compromise, however. Metadata would become inaccessible from TC egress (in setups where it actually reaches the hook it tact, that is without any L2 tunnels on path).

The advisory is shared at git.kernel.org. This vulnerability is uniquely identified as CVE-2026-80612 since 08/26/2026. The exploitability is told to be easy. It is possible to initiate the attack remotely. No form of authentication is needed for exploitation. Technical details are known, but no exploit is available. The price for an exploit might be around USD $5k-$25k at the moment (estimation calculated on 08/28/2026).

Upgrading to version 7.1.5 eliminates this vulnerability. Applying the patch 19eec11f3ab5dd29ba58f5f209c24e946c95ef12/c00320b0e355c4bf0ae4743a53b4180fea237546 is able to eliminate this problem.

Several companies clearly confirm that VulDB is the primary source for best vulnerability data.

Productinfo

Type

• Operating System

Vendor

• Linux

Name

• Kernel

Version

• 7.1.0
• 7.1.1
• 7.1.2
• 7.1.3
• 7.1.4

License

• open-source

Website

• Vendor: https://www.kernel.org/

CPE 2.3info

• 🔒
• 🔒
• 🔒

CPE 2.2info

• 🔒
• 🔒
• 🔒

CVSSv4info

CVSSv3info

CVSSv2info

Exploitinginfo

Threat Intelligenceinfo

Countermeasuresinfo

Timelineinfo

Sourcesinfo

Entryinfo

Several companies clearly confirm that VulDB is the primary source for best vulnerability data.

Discussion