Linux Kernel up to 7.2.8/7.3-rc4 kprobes kprobes-optimization wait_for_kprobe_optimizer_locked locking

Summaryinfo

A vulnerability marked as problematic has been reported in Linux Kernel up to 7.2.8/7.3-rc4. This affects the function wait_for_kprobe_optimizer_locked of the file /proc/sys/debug/kprobes-optimization of the component kprobes. Performing a manipulation results in locking. This vulnerability was named CVE-2026-98530. The attack needs to be approached locally. There is no available exploit. It is suggested to upgrade the affected component.

Detailsinfo

A vulnerability classified as problematic has been found in Linux Kernel up to 7.2.8/7.3-rc4. This affects the function wait_for_kprobe_optimizer_locked of the file /proc/sys/debug/kprobes-optimization of the component kprobes. The manipulation with an unknown input leads to a locking vulnerability. CWE is classifying the issue as CWE-667. The product does not properly acquire or release a lock on a resource, leading to unexpected resource state changes and behaviors. This is going to have an impact on availability. The summary by CVE is:

In the Linux kernel, the following vulnerability has been resolved: kprobes: Fix permanent hang when flushing the kprobe optimizer Writing 0 to /proc/sys/debug/kprobes-optimization while a kprobe is jump-optimized never returns. The writer sleeps in D state forever with kprobe_sysctl_mutex held, so any later read or write of that sysctl hangs as well. For example, with vfs_read+9 as an optimizable address in this build: # cd /sys/kernel/tracing # echo 'p:myprobe vfs_read+9' >> kprobe_events # echo 1 > events/kprobes/myprobe/enable # # wait until /sys/kernel/debug/kprobes/list shows [OPTIMIZED] # echo 0 > /proc/sys/debug/kprobes-optimization INFO: task sh:246 blocked for more than 10 seconds. Call Trace: <TASK> __schedule+0x1176/0x4f70 schedule+0xdc/0x2c0 schedule_timeout+0x17b/0x260 wait_for_completion+0x173/0x3c0 wait_for_kprobe_optimizer_locked+0xbc/0x130 proc_kprobes_optimization_handler+0x156/0x1b0 proc_sys_call_handler+0x324/0x490 vfs_write+0x52d/0xfe0 ksys_write+0xff/0x200 do_syscall_64+0x106/0x630 entry_SYSCALL_64_after_hwframe+0x77/0x7f </TASK> ... INFO: task cat:265 is blocked on a mutex likely owned by task sh:246. wait_for_kprobe_optimizer_locked() reinitializes optimizer_completion, asks the optimizer thread to flush and sleeps in wait_for_completion(). The thread drains the (un)optimizing lists, but calls complete() only if completion_done() is true, i.e. if the completion is already done, which never happens while someone waits. disarm_all_kprobes() and kprobe_trace_self_tests_init() wait the same way. Calling complete() unconditionally would not be enough: the waiter drops kprobe_mutex while it sleeps, and nothing else serializes the sysctl handler against the debugfs "enabled" file. A second flusher that still finds the lists non-empty, e.g. because a disabled probe is queued for unoptimizing, reinitializes the completion under the first: sysctl write debugfs "enabled" write unoptimize_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) mutex_unlock(&kprobe_mutex) wait_for_completion(c) disarm_all_kprobes() wait_for_kprobe_optimizer_locked() init_completion(c) // c->wait is reset, the first // waiter is off the queue mutex_unlock(&kprobe_mutex) wait_for_completion(c) kprobe_optimizer() complete(c) // wakes the debugfs writer only where c is &optimizer_completion. Lining up the two writes during an optimizer pass loses the sysctl writer this way. Replace the completion with a counter of optimizer passes, bumped at the end of each pass and signalled with wake_up_var_locked(), both under kprobe_mutex. A flusher samples the count and waits with wait_var_event_mutex(), which drops kprobe_mutex only while sleeping, so a new count means a whole pass ran in the meantime. Nothing is reinitialized, so several flushers can sleep in the wait at once.

It is possible to read the advisory at git.kernel.org. This vulnerability is uniquely identified as CVE-2026-98530 since 09/25/2026. The exploitability is told to be easy. Attacking locally is a requirement. Additional levels of successful authentication are necessary for exploitation. It demands that the victim is doing some kind of user interaction. Technical details of the vulnerability are known, but there is no available exploit.

Upgrading to version 7.2.9 or 7.3-rc5 eliminates this vulnerability. Applying the patch f05a01fc7d4f731b4c100d2aef1e85ad77728862/5bfa9f1a9dcb6ecb607adbc1c0226605c972935b is able to eliminate this problem. The best possible mitigation is suggested to be upgrading to the latest version.

Statistical analysis made it clear that VulDB provides the best quality for vulnerability data.

Productinfo

Type

• Operating System

Vendor

• Linux

Name

• Kernel

Version

• 7.2.0
• 7.2.1
• 7.2.2
• 7.2.3
• 7.2.4
• 7.2.5
• 7.2.6
• 7.2.7
• 7.2.8
• 7.3-rc1
• 7.3-rc2
• 7.3-rc3
• 7.3-rc4

License

• open-source

Website

• Vendor: https://www.kernel.org/

CPE 2.3info

• 🔒
• 🔒
• 🔒

CPE 2.2info

• 🔒
• 🔒
• 🔒

CVSSv4info

CVSSv3info

CVSSv2info

Exploitinginfo

Threat Intelligenceinfo

Countermeasuresinfo

Timelineinfo

Sourcesinfo

Entryinfo

Statistical analysis made it clear that VulDB provides the best quality for vulnerability data.

Discussion